Foro de Filatelia Argentina

30cMH1E2 pane used for partial plating: the pane

Here is a partial plating of the 30c from a block of 89 of the 30c-MH (Hacienda) 1E2. This block is missing position 95 and the 10th column. I find that the plate was made either with two blocks of 50 dies (top and bottom halves), or with four quadrants of 25 each. The plate does not have enough wear for me to conclusively prove that halves or quarters were used. In these pages I line up each row from the top half with its counterpart in the bottom half.

30cMH1E2 pane used for partial plating: the overprint

Here are the ones that look fairly different from the norm.

Position 2



Position 3



Position 13



Position 14



Position 21



Position 23



Position 28



Position 33



Position 35



Position 39



Position 43



Position 49



Position 52



Position 58



Position 62



Position 64



Position 83



Position 86



Position 91



Position 92



Position 93

30cMH1E2 pane used for partial plating: the quadrants

Here are the major varieties for each position. If the stamp has more than one plate flaw, I have only kept here the one that is useful to figure out how the plate was assembled.

Upper Left



Upper Right



Lower Left



Lower Right

30cMH1E2 pane used for partial plating: rows 0 and 5

Position 2



Position 3







Position 5





Position 7





Position 9





Position 51







Position 53





Position 54







Position 55





Position 57





Position 59

30cMH1E2 pane used for partial plating: rows 1 and 6


Position 11







Position 12





Position 13





Position 14





Position 16





Position 17







Position 19





Position 64





Position 65





Position 66





Position 67





Position 69

30cMH1E2 pane used for partial plating: rows 2 and 7



Position 23





Position 25





Position 28





Position 71





Position 72





Position 73





Position 75





Position 78

30cMH1E2 pane used for partial plating: rows 3 and 8


Position 33





Position 36







Position 38





Position 81







Position 83





Position 87

30cMH1E2 pane used for partial plating: rows 4 and 9



Position 41



Position 42







Position 44





Position 46





Position 47





Position 49







Position 91





Position 93





Position 94





Position 96







Position 97





Position 99

rubiera escribió:30cMH1E2 pane used for partial plating: the pane

Here is a partial plating of the 30c from a block of 89 of the 30c-MH (Hacienda) 1E2. This block is missing position 95 and the 10th column. I find that the plate was made either with two blocks of 50 dies (top and bottom halves), or with four quadrants of 25 each. The plate does not have enough wear for me to conclusively prove that halves or quarters were used. In these pages I line up each row from the top half with its counterpart in the bottom half.

Tony,

I would start from a root block of 2x5 via 5x5 through to 10x10!? This would mean the columns 5 and 6 being pretty similar!

The red and the green indicated dots repeat alternately; the blue ones are in every stamp!



The dot belongs to the back-ground colour:



The slash belongs to the back-ground colour:

Thanks, Rein. I looked all over for these posts and couldn't find them. I knew that you had done some work on these.

tony

rubiera escribió:Thanks, Rein. I looked all over for these posts and couldn't find them. I knew that you had done some work on these.

tony

Tony,

I had some trouble finding them myself! Contributing some 2500 postings in 16 months is asking for trouble! And if the board is splitting things up in anglosaxon and castellano you do not really know how and where to look!

rc2500

and I looked really hard because I did not want to reinvent the wheel. I knew for sure you had done some work....anyways.

tony